Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Maintenance & Mods (D4)

Brake Pad Warning Light
Post Reply  Down to end
Page 2 of 2 <12
Emmet McKnight
 


Member Since: 19 Jan 2018
Location: Derry
Posts: 265

Ireland 2006 Discovery 3 TDV6 HSE Auto Zermatt SilverDiscovery 3

Ali1971 wrote:
Question ? Does the rear handbrake shoes let you know when they are worn? Just thinking about an ongoing fault currently which pops up from time to time?


Rear hand brake shoes should never wear, that’s if the hand brake is adjusted correctly they should never come in contact with a moving hub hence no wear.
  
Post #202731410th Feb 2019 7:17 pm
View user's profile Send private message View poster's gallery Reply with quote
jamez79
 


Member Since: 03 Sep 2018
Location: Staffordshire
Posts: 565

United Kingdom 2012 Discovery 4 3.0 SDV6 XS Auto Indus SilverDiscovery 4

I get the orange light with a "brake pads worn" warning which I think is down to the sensor i damaged when changing the rear pads. I've got a new sensor (and new discs/pads for the front) so will change the sensor and check pads and disca all round at the same time.

Not long after I'd had my motor, I got the flashing red brake warning and the epb wouldn't release. A few days prior to it refusing to release, it made an awful squealing noise when being applied (i think i also had the red flashing brake symbol but can't recall exactly). I had to release the epb manually and left it off until I could get round to changing the epb pads, discs and brake pads which I did using Bodsy's brake bible. Turns out they hadn't been adjusted correctly by the previous owner/service centre and had worn away. Following Bodsy's guide, I swapped the bits over, adjusted it correctly and (Touch wood) not had a problem since.

Should be something you can sort yourself just by following his guide. Thumbs Up
   
Post #203266928th Feb 2019 10:38 am
View user's profile Send private message View poster's gallery Reply with quote
sasdiscos
 


Member Since: 22 Feb 2013
Location: Northants
Posts: 885

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Bali BlueDiscovery 4

Shoes will wear if you pull away using auto release.

Steve
 You remind me of a younger me, not much younger mind...perhaps even a little older!  
Post #203274028th Feb 2019 3:13 pm
View user's profile Send private message View poster's gallery Reply with quote
Sheepy
 


Member Since: 20 Feb 2013
Location: Bedfordshire
Posts: 630

United Kingdom 2010 Discovery 4 3.0 TDV6 GS Auto Zermatt SilverDiscovery 4

I had this on mine a while back, turned out that the sensor wire had slipped out of a clip and was rubbing on the rotating hub which partially wore through the cable and thus as the cable flapped about, the light came on and went off.

One way to isolate it to the actual sensor/cable is to unplug the sensor from the wiring loom and replace it with a little wire loop pushed into the loom plug (I used a bent paper clip!). If the light never comes on after this, then the issue is in the sensor or the sensor cable.
  
Post #203275528th Feb 2019 3:58 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 2 of 2 <12
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site