Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Technical (D3)

D3 TDV6 Cranks but does not start or Starts and Cuts imm
Post Reply  Down to end
Page 1 of 1
OutlawLR3
 


Member Since: 12 Sep 2019
Location: Bremen
Posts: 8

Germany 2005 Discovery 3 TDV6 HSE Auto Galway GreenDiscovery 3
D3 TDV6 Cranks but does not start or Starts and Cuts imm

Hey Folks, i have a 2004 LR3 Discovery 2.7 TDV6 and it worked like a charm until 399600km. I(diot) pressurewashed my engine bay and then the trouble began.

I had some transmission and transfercase faults. I could delete them with nanocom. Later that day the car itself cycled the locks and made some weird flashing. I put silica dry pads in the car and disconnected the battery over night.

Next day the flashing and locks-problem was gone, and i was happy as mf. But as i wanted to start it, it immediately cuttet off.

If i just put the key to ignition stage 2 it makes some weird clanks 6 times, then its silent. And wont start, in the clank-time the car starts but cuts out after 1-2 seconds. After the clank time its just cranking but does not start.

these are the errorcodes from Nanocom:

FAULT 1 OF 14
ECU: Engine Management
CODE:P140A
Exhaust gas recirculation sensor C - circuit low
(PENDING)
GENERAL FAILURE INFORMATION -
NO SUBTYPE INFORMATION.

FAULT 2 OF 14
ECU: Engine Management
CODE:P0562
System voltage low
(PENDING)
GENERAL FAILURE INFORMATION -
NO SUBTYPE INFORMATION.

FAULT 3 OF 14
ECU: Engine Management
CODE:P0A09
DC/DC converter fault circuit low
(PENDING)
GENERAL FAILURE INFORMATION -
NO SUBTYPE INFORMATION.

FAULT 4 OF 14
ECU: Engine Management
CODE:P1136
Control box fan circuit
(PENDING)
GENERAL FAILURE INFORMATION -
NO SUBTYPE INFORMATION.

FAULT 9 OF 14
ECU: Airbags/SRS
CODE:B1A55
Crash record output circuit
(PERMANENT)
GENERAL ELECTRICAL FAILURE -
CIRCUIT SHORT TO GROUND OR OPEN.


These dont make sense to me, and i dont know where to start... may you ppl help me?

Thanks so much in advance.
  
Post #212049112th Feb 2020 8:41 am
View user's profile Send private message View poster's gallery Reply with quote
Hardware
 


Member Since: 28 Jun 2016
Location: Hiding under the M60
Posts: 12676

United Kingdom 2011 Discovery 4 3.0 SDV6 XS Auto Sumatra BlackDiscovery 4

Someone will no doubt provide more detail but I recall the connections behind the battery don't like getting wet.
 .


Dean
====================================

2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer Sad ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms 
 
Post #212050212th Feb 2020 9:13 am
View user's profile Send private message View poster's gallery Reply with quote
OutlawLR3
 


Member Since: 12 Sep 2019
Location: Bremen
Posts: 8

Germany 2005 Discovery 3 TDV6 HSE Auto Galway GreenDiscovery 3

Thank you, but i dried them really careful. I hope some had solved this special problem as reflashing the ecu did not bring any improvements. (Someone said this could help but in my case id didnt help).
  
Post #212050712th Feb 2020 9:43 am
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10337

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

the ecu's behind the battery get wet.

best remove them and dry them slowly.

However this makes me think you will need a new engine ecu

FAULT 3 OF 14
ECU: Engine Management
CODE:P0A09
DC/DC converter fault circuit low
  
Post #212062812th Feb 2020 5:20 pm
View user's profile Send private message View poster's gallery Reply with quote
bembo449
 


Member Since: 14 Jan 2020
Location: Gainsborough
Posts: 256


could try the bag of rice trick ? saved many a mobile phone over the years
  
Post #212063712th Feb 2020 5:53 pm
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10337

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

They only work if you disconnect the power quickly.

2 of them codes makes me think the ecu is toast.
  
Post #212064912th Feb 2020 6:42 pm
View user's profile Send private message View poster's gallery Reply with quote
OutlawLR3
 


Member Since: 12 Sep 2019
Location: Bremen
Posts: 8

Germany 2005 Discovery 3 TDV6 HSE Auto Galway GreenDiscovery 3

hey what do you mean with they only work if you disconnect the power quickly?


I dismantled the ecu and checked the inside. everything is good there so far.

is it possible to use a used ecu?
  
Post #212066612th Feb 2020 8:20 pm
View user's profile Send private message View poster's gallery Reply with quote
OutlawLR3
 


Member Since: 12 Sep 2019
Location: Bremen
Posts: 8

Germany 2005 Discovery 3 TDV6 HSE Auto Galway GreenDiscovery 3

So, she is back at live, i bought another D3 with an engine jam and swapped all the electronics, so i guess the engine ECU is toast. Now she runs great again.
  
Post #212911718th Mar 2020 12:16 pm
View user's profile Send private message View poster's gallery Reply with quote
Hardware
 


Member Since: 28 Jun 2016
Location: Hiding under the M60
Posts: 12676

United Kingdom 2011 Discovery 4 3.0 SDV6 XS Auto Sumatra BlackDiscovery 4

Good news. Glad someone has some today.
 .


Dean
====================================

2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer Sad ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms 
 
Post #212914718th Mar 2020 1:31 pm
View user's profile Send private message View poster's gallery Reply with quote
Flack
 


Member Since: 06 Sep 2006
Location: Preston Lancashire
Posts: 6224

England 2007 Discovery 3 TDV6 XS Auto Stornoway GreyDiscovery 3

I have had a couple of PCm Ecu's fail due to water ingress, it fries some parts on the bottom of the main board, it looks ok even drying it out, but the damage is already done.
The worst one I had was full of water.

Flack Thumbs Up
  
Post #212916118th Mar 2020 2:16 pm
View user's profile Send private message View poster's gallery Send e-mail Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site