Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO3.CO.UK as a guest - Register to take part or Log In
Flack
Member Since: 06 Sep 2006
Location: Preston Lancashire
Posts: 6234
|
You have to be careful with the new sensors, I have run in to problems just fitting one sensor, if you look at the pins some of the newer sensors do not have the same number of pins, so fitting just one can upset the whole calibration.
It seems to be ok when you fit a full set.
But you need to check what has been suggested above with the wiring especially the plug, it might look ok from the outside, but most fail inside the wire where it can not be seen.
Test the wire close to the plug and then at the pin inside the plug.
Flack
|
18th Feb 2018 7:12 pm |
|
|
Karl85
Member Since: 13 Feb 2018
Location: Claydon
Posts: 4
|
Thanks for the help I had put the wrong sensor on the wrong side I've changed it now and it's all fine. Thanks for all comments and suggestion.
|
18th Feb 2018 10:34 pm |
|
|
Randylover
Member Since: 31 Jan 2011
Location: Staffordshire
Posts: 1172
|
05 TDV6,"S" in all colourcoded Zermatt silver,7 seats winter pack HK 6cd stereo,Dual climate,Xenons,
Mods:
Re-Con Engine,De-Tango,Reverse camera,Fog/DRl lights,Aux Battery, perm Aux socket in boot,LED Volt meters in roof panel,Built in tom tom, Strobes fitted in grille, Aux switches for trailer lights fitted in roof panel,Roof Rails,Grille conversion
|
18th Feb 2018 11:05 pm |
|
|
Robfal
Member Since: 28 Jan 2018
Location: Wick
Posts: 9
|
Can anyone tell me on the right rear sensor where the red/grey wire the yellow/grey and the blue/grey wires go on pins 1,4and 5 and which one is feed,earth and signal wires.
Thanks
Rob
|
10th Mar 2018 5:38 pm |
|
|
Compusmentis
Member Since: 18 Feb 2016
Location: Effingham
Posts: 237
|
Search on here for posts from Allan_T. He has some schematics which were a huge help when i was trying to fix mine New gearbox & TC, 3 x front wheel bearings, belts changed, new oil pump, new battery, new rear prop, new front prop, new front diff, front arb refurbed, front cv boot kit, egr blank and BAS software patch, full rear suspension / drivelive rebuild, new front arms, LED trailer light fix, split charge.
Never had a 107, 90 or 127, but have had most of the rest!
|
10th Mar 2018 9:48 pm |
|
|
Robfal
Member Since: 28 Jan 2018
Location: Wick
Posts: 9
|
Ok I have been back at this again and I have connected three new wires direct from the ecu to the right rear sensor but no difference what I can’t understand is why I am getting 4.9v on the grey yellow wire which should be earth I am puzzled with this one
Rob
|
18th Mar 2018 9:04 am |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1782
|
According to my diagram - pin 5 has the yellow wire and is 5 volts
Pin 4 has blue wire and is the signal
Pin 1 has the red wire and is ground
Hope that helps
|
18th Mar 2018 9:26 am |
|
|
Robfal
Member Since: 28 Jan 2018
Location: Wick
Posts: 9
|
hi thanks for that I was going on information that I got when I ordered a new plug for the sensor it had said that the yellow grey was earth but obviously was wrong I wonder if this would have wrecked the new sensor
rob
|
18th Mar 2018 10:25 am |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1782
|
plug it up the right way and see if it works
|
18th Mar 2018 10:39 pm |
|
|
|
Posting Rules
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO3.CO.UK is independent and not affiliated to Land Rover.