AWD man
Member Since: 03 Jul 2009
Location: In Drag
Posts: 831
|
The centre section of the lower valance removes too Keith 
The panel in your bumper houses the towing electrics and emergency towing eye
The location of the towbar fixing hole is underneith (behind that centre section) 57 RRS TDV8
BAS Map
D3: Gone but not forgotten
Last edited by AWD man on 15th Feb 2010 12:21 am. Edited 1 time in total
|
 11th Feb 2010 1:00 pm |
|
|
Russell
Member Since: 24 Aug 2007
Location: Kent
Posts: 10564
|
Does the lower tray it onto the original rear bumper or is it a case of a whole new bumper? Would it fit onto the D4 rear bumper? MY17 D5 1st Edition Namib Orange
MY15 D4 HSE Kaikoura Stone
MY12 D4 HSE Nara Bronze Sold and gone
MY11 D4 HSE Stornaway Grey Sold and gone
D3 S spec Silver Sold and gone
Tow bar, full length roof bars, side steps, tow bar storage unit, surround camers.
D4 camera club
|
| 12th Feb 2010 10:49 am |
|
|
Helli2020
Member Since: 07 Feb 2010
Location: Essex
Posts: 17
|
wow i'm loving that front end................where can you get the kit from both front and rear?
|
| 12th Feb 2010 11:24 am |
|
|
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15214
 
|
Russell wrote: Would it fit onto the D4 rear bumper?
Reckon the D4 rear bumper is the same as the D3 MY09 bumper and therefore should fit. I was a normal heterosexual chap, but in these new woke awakenings I now identify as a Wardrobe.
|
| 12th Feb 2010 12:09 pm |
|
|
AWD man
Member Since: 03 Jul 2009
Location: In Drag
Posts: 831
|
ronp wrote:Russell wrote: Would it fit onto the D4 rear bumper?
Reckon the D4 rear bumper is the same as the D3 MY09 bumper and therefore should fit.
+1 57 RRS TDV8
BAS Map
D3: Gone but not forgotten
|
| 12th Feb 2010 12:55 pm |
|
|
oddboy
Member Since: 29 Oct 2009
Location: norfolk
Posts: 472
|
the D4 bumper fits straight on the D3 mine is being fitted today Richard
club none owner
|
| 12th Feb 2010 1:19 pm |
|
|
beetlejuice
Member Since: 14 Feb 2010
Location: skegness lincolnshire
Posts: 1
 
|
i have just purchased the samr disco3 could you tell me where i can get a front bumper like this one and also how come your land rover seems to be a lot lower than mine have you done something to the suspension,thnx 
|
| 14th Feb 2010 10:22 pm |
|
|
90BHP
Member Since: 18 Oct 2006
Location: Half way along the road on the right
Posts: 3706
|
Looks like it's on 20's and either suspension is slightly compressed due to terrain, or it may be in access height, - look at negative camber on front wheels (tops inward). "To finish first, one first has to finish ...."
|
| 14th Feb 2010 10:37 pm |
|
|
AWD man
Member Since: 03 Jul 2009
Location: In Drag
Posts: 831
|
The bumper "kit" is the one TLO's been offering in the for sale section, but I'm not 100% sure he's still offering it... look on ebay, some dealers are still selling them... IT does not seam to have an official name though.
It's not available in Zambezi either, that's a spray shop job, I ordered the stornoway grey kit... ideal as a primer colour... spraying cost me £130.
Yes as 90bhp said, I've got 20" V spokes with 295 UHP grabbers, and in that pic it's in access mode, so lower than normal. 57 RRS TDV8
BAS Map
D3: Gone but not forgotten
|
| 15th Feb 2010 12:15 am |
|
|
AWD man
Member Since: 03 Jul 2009
Location: In Drag
Posts: 831
|
Cheers SHG
Distructions came this morning 57 RRS TDV8
BAS Map
D3: Gone but not forgotten
|
| 15th Feb 2010 1:48 pm |
|
|
AWD man
Member Since: 03 Jul 2009
Location: In Drag
Posts: 831
|
Well it's been finally warm enough (as per LR instructions and not as a result of being a southern wimp)
to fit the rear kit
Near side trim went on a dream (after taking D3 to local exhaust centre to free off the nylock nuts currently holding the harmonic dampers so I could locate the new trim brackets on the same bolt).
Offside not so dreamlike... I think I've got the bracket on too low..but adjusting it is a right bitch with everything in place...and my lad came home from nursery with a high temp so SWMBO cut short my car time....so may have another go at it tonight.
Overall (even with the slight gap on the offside trim) very happy!
Pics will follow later (Mrs has D3 today so will wait on her return)
Might call on a few votes either to get the trim colour matched in Zambezi...or leave it stock Brunel Silver 57 RRS TDV8
BAS Map
D3: Gone but not forgotten
|
| 20th May 2010 12:08 pm |
|
|
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15214
|
Are you angling the exhaust exit
[as recommended by LR with their kit].
Does it really need it ?
Need to get around now to fitting mine, but not really looked at all the ins and outs.
Sounds like the harmonic damper nuts will be an interesting one.  I was a normal heterosexual chap, but in these new woke awakenings I now identify as a Wardrobe.
|
| 21st May 2010 8:42 am |
|
|
Renton
Member Since: 13 Jan 2009
Location: Somewhere in the middle
Posts: 1718
|
Hi Ron,
Did you look at this thread? http://disco3.co.uk/forum/topic34148.html?highlight=
I don't actually think you need to angle the trims. But imho it looks silly seeing smoke coming from below the trim and not through the exhausts. CLUB ILLEGAL CAR WASHERS
|
| 21st May 2010 9:29 am |
|
|
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15214
|
Yep thanks, already got that saved in my D3 favorites in readiness to study.
I was a normal heterosexual chap, but in these new woke awakenings I now identify as a Wardrobe.
|
| 21st May 2010 9:44 am |
|
|
AWD man
Member Since: 03 Jul 2009
Location: In Drag
Posts: 831
|
I think I might investigate these angled exhaust trims more....
The exhaust doesn't exit through the "hole" in the underside of the trim (as I expected) but more to the outer edge of each side.... which is obviously causing turbulence and heat... resulting in the 3M tape melting  and sooty stains now edging up the gap between the trim and the bumper...
I'm assuming these angled exhaust trims just direct the flow away from the trim (down towards the large hole)
because that's all that's needed. 57 RRS TDV8
BAS Map
D3: Gone but not forgotten
|
| 24th May 2010 8:36 am |
|
|
