Member Since: 08 Mar 2018
Location: italia
Posts: 8
hello francesco, unfortunately I'm stationary, I can not find a mechanic able to perform this operation. so I will be forced to install the block arb. I can not create a complete differential without having a mechanic able to do the job.
27th Jul 2018 2:55 pm
francescor75
Member Since: 07 Jul 2018
Location: Palermo
Posts: 88
I can contact you via mobile phone ?
27th Jul 2018 4:26 pm
DiscoLuca
Member Since: 08 Mar 2018
Location: italia
Posts: 8
I see the topic ist a few years old but i actualy have the same problem and maybe there ist still someone out there who can help.
Actual state ist i have two disco with different engine falls, i pulled the complete drivetrain on both and while my mechanic build one engine out of the best parts from both, i try to put all the best parts in my planed runner.
That means i have one complete E-Diff with wiring an all and need to know what to do to swap it in to the standart one.
Thanks Guys
3rd Aug 2024 9:12 pm
francescor75
Member Since: 07 Jul 2018
Location: Palermo
Posts: 88
very simple you have to connect all the wiring, install the e-diff and finally activate everything in your car config (idiitool can do it)Discovery 3 MY2005
Engine 2.7 diesel
HSE - bonatti Grey
E-diff - retrofit
Rear a/c - retrofit
Adaptive Cruise Control - retrofit
Bluetooth factory feat - retrofit
Smog sensor - retrofit
Roof Rosen G10 DVD - Retrofit
Tire pressure control monitor - work in progress
Elenctric column steering - work in pogress
IIDtool BT
Is it possible to just plug and play from one to the other or ist there some work on the wiring at the Disco that came without the locker?
I have the Nanocom i think IT IS possible to program with that tool.
Thanks
3rd Aug 2024 9:43 pm
francescor75
Member Since: 07 Jul 2018
Location: Palermo
Posts: 88
I don't know nanocom so I don't know what it can do. I have idiitoll and he does everything 😉
if your chassis has three rectangular connectors behind the left rear wheel (one of which is blue) you already have most of the wiring inside and you only need the lower part that goes under the frame
if you only have two connectors and you don't have the blue one you have to assemble everything, but it's easy and fun.
If you need help I'm here
Please note it must be active in car configDiscovery 3 MY2005
Engine 2.7 diesel
HSE - bonatti Grey
E-diff - retrofit
Rear a/c - retrofit
Adaptive Cruise Control - retrofit
Bluetooth factory feat - retrofit
Smog sensor - retrofit
Roof Rosen G10 DVD - Retrofit
Tire pressure control monitor - work in progress
Elenctric column steering - work in pogress
IIDtool BT
Nanocom ist from similar to faultmate and also from Blackboxsolutions i think it is possible
The doner ist complete Iiclude the blue connector the other one didn't have it
5th Aug 2024 8:44 am
francescor75
Member Since: 07 Jul 2018
Location: Palermo
Posts: 88
if the receiver does not have the blue connector you must install all the wiring and activate ediffDiscovery 3 MY2005
Engine 2.7 diesel
HSE - bonatti Grey
E-diff - retrofit
Rear a/c - retrofit
Adaptive Cruise Control - retrofit
Bluetooth factory feat - retrofit
Smog sensor - retrofit
Roof Rosen G10 DVD - Retrofit
Tire pressure control monitor - work in progress
Elenctric column steering - work in pogress
IIDtool BT
OK at the moment i have the blue connector inside and disassemble IT from the wiring harnes
First Problem i found there ist a canbus cable yellow/black and yellow/Brown that went in to the plack connector but in the reciever there are those pins already used (same colors)
The lines end in the purple connector on the Controlunit and from there an other pair Same color to the Front
5th Aug 2024 10:51 am
francescor75
Member Since: 07 Jul 2018
Location: Palermo
Posts: 88
Where can i connect the canbus wiring?
There is a pink connector at the dif CPU with one can bus pair that disapers under the centerconsole between the fronseats the other pair leads into the black connector in the rear wheelarch at the reciever car is a canbus pair from exact the same Pins in the black connector straight to the centerconsole.
Greetings
19th Aug 2024 10:43 am
francescor75
Member Since: 07 Jul 2018
Location: Palermo
Posts: 88
you can connect at any point, be careful:
- respect the colors
- twist the cables well otherwise you will have problemsDiscovery 3 MY2005
Engine 2.7 diesel
HSE - bonatti Grey
E-diff - retrofit
Rear a/c - retrofit
Adaptive Cruise Control - retrofit
Bluetooth factory feat - retrofit
Smog sensor - retrofit
Roof Rosen G10 DVD - Retrofit
Tire pressure control monitor - work in progress
Elenctric column steering - work in pogress
IIDtool BT
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum