Member Since: 01 Oct 2008
Location: in the middle
Posts: 557
Nanocom Timed Climate Settings
Hi Guys,
I've had my D4 a few weeks now and now have my D4 license for my nanocom evolution and i'm looking to enable timed climate without remote.
Im currently looking through the CCF config on the Genisis website and these are the settings I see
Under Heating and Ventilation
Additional Heater - Fuel fired heater (FFH) change to Fuel Fired Parking Heater (FFPH)
Callstart of Parking Heater - "Without Callstart" change to "Callstart via Radio"
Park Heater - "Not Fitted" change to "Fitted"
but for the life of me i can't find A "Timed Climate" setting that has been mentioned in other posts.
Can anyone point my in the right direction??
Many Thanks in advance.
Cheers
Lee
16th Jan 2015 10:42 pm
geoff.
Member Since: 24 Jan 2010
Location: West kent
Posts: 8531
which timed climate setting you talking about lee
16th Jan 2015 10:45 pm
lee157
Member Since: 01 Oct 2008
Location: in the middle
Posts: 557
Hi Geoff,
I was reading this thread and it referred to setting timed climate to "enable" but can't find the setting within the CCF file.
I'm hoping to enable Timed Climate on mine tomorrow - just controlled on screen and no remote. Looking through this thread I see stenh02 mentions these 3 settings....
stenh02 wrote:
I thought there were three settings to change to get the Timed climate working with the IIDTool
"Timed Climate" to "Enabled"
"Fuel Burning Heater" to "Fitted Parking Heat"
"FBH Call Start" to "Fitted Radio"
Obviously this is without the remote.
then Wiggs mentions another setting....
wiggs wrote:
There is normally 3 settings to change
Last one is .. Additional heater .. FFPH
So do I need to modify 4 settings or 3, and where do I find them in the CCF? Only had the tool (non BT) a day, so just getting the hang of it, but really pleased to be able to communicate with my vehicle at last
Thanks
Cheers
Lee
16th Jan 2015 11:05 pm
geoff.
Member Since: 24 Jan 2010
Location: West kent
Posts: 8531
what you've put should be right , check your screen it should be there
16th Jan 2015 11:07 pm
lee157
Member Since: 01 Oct 2008
Location: in the middle
Posts: 557
Thanks Geoff,
I've got the editor set to Advance mode and under heating and ventilation it only goes as far as Smog Sensor and Sun Sensor, end of page.
I can't see "timed climate" anywhere
16th Jan 2015 11:11 pm
geoff.
Member Since: 24 Jan 2010
Location: West kent
Posts: 8531
Lee
Send me your vin I will have a look
16th Jan 2015 11:15 pm
lee157
Member Since: 01 Oct 2008
Location: in the middle
Posts: 557
PM'd you
16th Jan 2015 11:18 pm
geoff.
Member Since: 24 Jan 2010
Location: West kent
Posts: 8531
messaged you
16th Jan 2015 11:27 pm
lee157
Member Since: 01 Oct 2008
Location: in the middle
Posts: 557
Thanks Geoff
16th Jan 2015 11:32 pm
Perdi's Dad
Member Since: 04 Sep 2013
Location: Hertfordshire
Posts: 188
Hi all.
I know this is an old thread but help. I managed to activate the timed heater then did some thing else and it fell off.
Can some one help me with what I need to activate on the nanocom to get the timed heater? ?
Thank you! !Upgrades so far - , rear ladder from prospeed , front and rear light guards G4 style roof rack and 4 lightforce spots on the rack! Xenon lights
15th Feb 2016 10:42 pm
bielec
Member Since: 01 Sep 2016
Location: Aberdeenshire
Posts: 3
I know the thread is old but I have the same problem using CCF editor and Nnocom. Where is the "Timed Climate" setting?
IID Pro MV License - D3, D4 & RRS - Enabling, Updates, D4 & RRS Timed / Remote Climate, D4 Bluetooth fitting
PM me for details
Owner of the original "Beanie" grille
D4 & RRS style D3 grilles made to order
1st Sep 2016 4:57 pm
bielec
Member Since: 01 Sep 2016
Location: Aberdeenshire
Posts: 3
Yes, thanks, I gat that far, but there are only two settings in there ("parking heat" and "call Radio") as described by the original poster above. All the forum posts suggest there are three settings. and the third one, "Timed Climate" is missing in that CCF. My VIN is SALLAAAG5FA743276 a 2014 disco 4 SE
Is this vehicle different from other models and perhaps does not have Timed Climate?
1st Sep 2016 6:44 pm
lee157
Member Since: 01 Oct 2008
Location: in the middle
Posts: 557
this is what you need to change , don't worry about the call by radio unless your fitting a remote receiver
Geoff"
Hope this helps.
BTW, this is using the nanocom evolution, so descriptions may differ with other equipment.
Lee
1st Sep 2016 7:03 pm
bielec
Member Since: 01 Sep 2016
Location: Aberdeenshire
Posts: 3
Thanks a lot Lee, that clarifies it. So there is a difference from the settings of earlier posts but there are still three settings. I presume that this enabled the Disco display to show timed operation of the heater.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum