Member Since: 27 Oct 2014
Location: South Lanarkshire
Posts: 42
New grills fitted
New front grill and side vents in black thanks to the dundonian
Before
After
19th Jun 2016 10:48 pm
Someone-Gone
Member Since: 21 Dec 2015
Location: Gone
Posts: 5117
They look really cool. 8)
19th Jun 2016 10:56 pm
lukeis
Member Since: 17 Mar 2016
Location: Sydney
Posts: 63
Looks good, but now you have to do the bonnet and the boot letters and lastly the door handles but definitely worth while!
Luckily you can get cheap letters from duckworths and just get the door handles sprayed.
I recently went through this exercise.. Never looked back!
20th Jun 2016 4:10 am
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Personally, I prefer "before".... Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
20th Jun 2016 7:51 am
Someone-Gone
Member Since: 21 Dec 2015
Location: Gone
Posts: 5117
Philistine!
20th Jun 2016 8:19 am
Mark6r
Member Since: 27 Oct 2014
Location: South Lanarkshire
Posts: 42
Just a wee refresh have been looking to do this for the last 18 months but never got round to it would take another 18 months to change the lettering and door handles at this rate.
Would certainly be cheaper than a new landmark we have been thinking about.
Might put the black grill centre in the grey outer and see how that looks.
20th Jun 2016 6:26 pm
Someone-Gone
Member Since: 21 Dec 2015
Location: Gone
Posts: 5117
20th Jun 2016 7:06 pm
lukeis
Member Since: 17 Mar 2016
Location: Sydney
Posts: 63
I know the feeling but i was worried that if i didn't do the badges as well it would look like a job half done. It really only took maybe 1.5 hours to change the boot/bonnett letters, the spray shop did the mirror caps and door handles for me...
here is my 2011 when i bought it two months ago, and what it looks like today..
21st Jun 2016 3:02 am
Barry C-All
Member Since: 13 Nov 2008
Location: Essex
Posts: 169
I have tried to remove the grille on my 2015 Disco 4, but cannot free it from whatever is holding it on it's lower edge. I have pulled it in almost every direction to no effect, but I don't want to get too powerful with it 'cos I don't want to break it, as it feels like it is held by a couple of screws that I have not seen.
Any suggestions will be welcome.
Regards, Barry C.
17th Sep 2016 7:41 pm
DaveT
Member Since: 01 Aug 2005
Location: Cornwall
Posts: 2572
open the bonnet, long screwdriver down from the top to release the tangs.Long succession of Disco's since 2001...
SIII Lightweight - neglected & rusting. Bulkhead, A panels, vent panel & outriggers now disintegrated - Next years project!
17th Sep 2016 9:36 pm
Narpy
Member Since: 18 Jul 2011
Location: Stockport
Posts: 7830
Member Since: 01 Aug 2005
Location: Cornwall
Posts: 2572
Presumed he meant the side vents - the front grille is easy Long succession of Disco's since 2001...
SIII Lightweight - neglected & rusting. Bulkhead, A panels, vent panel & outriggers now disintegrated - Next years project!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
