Member Since: 10 Jan 2020
Location: Marysville
Posts: 6
Remove the A-Bar brush protector for a 2007 Disco 3
Sorry if I am starting a topic that has already been addressed but I could not find a thread describing this issue.
Our recently purchased 2007 Disco3 has a black polyurethane brush protection bar mounted over the front grille and bumper. My wife and I don't like the look of the A-bar and prefer the standard grille and bumper. Has anyone removed the A-bar permanently? Wondering if the appearance would be just like the stock Disco3 that came from the factory without an A-bar. It does not have the hole plugs that cover the lower mounting bolts that I've seen on the aftermarket A-Bar. In otherwords, there is no access to the mounting bolts from the front. Any advice about removing the brush guard is greatly appreciated.
13th Feb 2020 8:08 pm
Andy Foster
Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551
Yes you can remove it and it will just be stock in appearance. However you’ll probably be left with some holes were the mounting fixings have been. When I fitted mine the brackets holding it one were mounted so that the fixing holes where out of sight. I seem to remember there was two versions with different mounting brackets.
AndyD4 MY15 SE TECH
D3 gone but never forgotten.
13th Feb 2020 8:39 pm
Andy Foster
Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551
Forgot to add if you get it off intact without any damage you’ll be able to sell it one for a tidy packet D4 MY15 SE TECH
D3 gone but never forgotten.
13th Feb 2020 8:40 pm
darrind
Member Since: 04 Jul 2008
Location: In A World of My Own!
Posts: 2863
Unfortunately there will be holes left where it comes off, however you may be able to swap the whole lot with someone for their bumper and a decent amount of cashMust stop buying shiny toys....
13th Feb 2020 8:52 pm
AH1_Pilot
Member Since: 10 Jan 2020
Location: Marysville
Posts: 6
Thanks for the reply, Andy. Did yours have 4 mounting bolts in the lower front that were covered with plastic caps? Mine has no visible bolt covers which makes me think that the lower attachment bolts must be accessed from behind the bumper.
Last edited by AH1_Pilot on 13th Feb 2020 8:54 pm. Edited 1 time in total
13th Feb 2020 8:53 pm
pwheeldon
Member Since: 15 Jan 2020
Location: West Yorks
Posts: 1446
Hi , there was a post about fitting one I think. I'll try and find it later for you. As said above what you get for the bar will probably pay for a replacement bumper anyway. I've seen listed for between £300-500 if in good condition.
CheersDiscovery 4 GS 2009 Auto Stornoway Grey
Discovery 3 s 2005 Auto Bonatti Grey Gone
Discovery 3 SE 2005 Manual Zambezi Silver Gone
Range Rover Sport HSE 2006 Black
Aston Martin DB7 VV
13th Feb 2020 8:54 pm
pwheeldon
Member Since: 15 Jan 2020
Location: West Yorks
Posts: 1446
Hi,
At the bottom of this post there is a link to download a PDF of the fitting instructions, hopefully that will help you with removing it.
Its a bit of a long shot, but I dont suppose you have the grills / guards for the spotlights do you? Mine came with them and I have managed to lose one!
CheersDiscovery 4 GS 2009 Auto Stornoway Grey
Discovery 3 s 2005 Auto Bonatti Grey Gone
Discovery 3 SE 2005 Manual Zambezi Silver Gone
Range Rover Sport HSE 2006 Black
Aston Martin DB7 VV
13th Feb 2020 9:19 pm
AH1_Pilot
Member Since: 10 Jan 2020
Location: Marysville
Posts: 6
Sorry, but my lamps have no grilles. The rest of the assembly is promised to a friend. Thanks for the link to the installation .pdf files. The second of the two files is the type that I have and the diagram gave me a much better idea of how the assembly is attached and how it can be removed.
14th Feb 2020 3:57 am
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 72786
AH1_Pilot, no way you can gave a site name like that without proof. As we like to say here, no pic = didn’t happen.
Only jealous BTW.
14th Feb 2020 5:12 am
Andy Foster
Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551
Mine was a secondhand one and only had fixing brackets at the top and bottom so no real visible holes when removed. I haven’t got the car now so can’t take any photos for you.D4 MY15 SE TECH
D3 gone but never forgotten.
14th Feb 2020 10:55 am
AH1_Pilot
Member Since: 10 Jan 2020
Location: Marysville
Posts: 6
Andy, Thanks for the reply
The style you had is certainly what I have too. Just received the correct installation diagram from pwheeldon on this forum. Planning to start the removal today if the garage isn't too cold
14th Feb 2020 2:07 pm
pwheeldon
Member Since: 15 Jan 2020
Location: West Yorks
Posts: 1446
Glad I could help, I get enough help on here its nice to do my bit at last!!Discovery 4 GS 2009 Auto Stornoway Grey
Discovery 3 s 2005 Auto Bonatti Grey Gone
Discovery 3 SE 2005 Manual Zambezi Silver Gone
Range Rover Sport HSE 2006 Black
Aston Martin DB7 VV
14th Feb 2020 2:13 pm
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1782
Pity I am not in the USA as I would take it off your hands
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
