Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Maintenance & Mods (D3)

Suspension advice required
Post Reply  Down to end
Page 1 of 1
the admiral
 


Member Since: 19 Oct 2015
Location: South east ,swale
Posts: 170

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3
Suspension advice required

I have had a suspension fault and got round to looking at it today.pictures show info , it was raising and lowering as normal.




Had wheel off and discovered connector to sensor had one clip missing and signs off corrosion, cleaned and will order new plug. Did notice this as you can see in picture below


Looks like someone's had a go before , is there a replacement loom for this ?

Anyway all back together and this is now displayed



Need some advise on the offending plug in picture and would this make the suspension drop when parks up . Thanks in advance
 D3 HSE 57 Buckingham Blue
box re-build
new TC

common sense is not common 
 
Post #16764303rd Jul 2016 10:57 am
View user's profile Send private message View poster's gallery Reply with quote
the admiral
 


Member Since: 19 Oct 2015
Location: South east ,swale
Posts: 170

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3

have been searching the interweb with no joy, there does not seem to be a pre-made loom for the rear air valve block ( height sensor ordered).

any advise would be great with how to repair/ splice out the bad bits. what sort of wire etc
 D3 HSE 57 Buckingham Blue
box re-build
new TC

common sense is not common 
 
Post #16765173rd Jul 2016 4:27 pm
View user's profile Send private message View poster's gallery Reply with quote
Ginner
 


Member Since: 28 May 2014
Location: Cheshire
Posts: 189

United Kingdom 2005 Discovery 3 4.4 V8 HSE Auto Zambezi SilverDiscovery 3

I had the same on my front drivers side, someone had took it off before and broke one of the retaining clips, it sprang off one day going over a bump, showed a similar fault on the dash and 4x4 screen. Pushed the multi plug back onto the sensor and wrapped a cable tie around it!

J
  
Post #16766623rd Jul 2016 9:09 pm
View user's profile Send private message View poster's gallery Reply with quote
the admiral
 


Member Since: 19 Oct 2015
Location: South east ,swale
Posts: 170

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3

the admiral wrote:
have been searching the interweb with no joy, there does not seem to be a pre-made loom for the rear air valve block ( height sensor ordered).

any advise would be great with how to repair/ splice out the bad bits. what sort of wire etc


harness to height sensor on order so will sort that one, its the other i'm concerned about. I thinks its going to the rear air block valve.
 D3 HSE 57 Buckingham Blue
box re-build
new TC

common sense is not common 
 
Post #16768584th Jul 2016 1:36 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site