Member Since: 15 Nov 2012
Location: Surrey
Posts: 190
Rear Prop Shart Bearing.
Hi,
So the MOT has thrown an advisory about the rear prop shaft bearing and it needs replacing. The £250 question is can I swap the bearing out this weekend ready for an event at the end of the month and then do the complete shaft in late sept/oct? The cost isn't an issue, its the work involved. Can the bearing be swapped without the complete shaft coming off???
I have the gear but no idea, Ramps, 3Ton stands, 3Ton jack and more tools that SWMBO needs to know about...
MY 06 HSE 2.7TDV6 with 153K on the clock.
TIA...Huggs.
D4 XS
D3 HSE(SOLD)
side steps, EGR blanked,3 flash +Clock Move
D4 XS 2012 For sale
D4 HSE 2015
V8 Upgrade Front brakes (AF)
155000 mile+ club
RAI
16000 lb winch
D4 As it comes...
Hampshire & Berkshire 4X4 Responder
26th Jul 2018 6:24 pm
L319
Member Since: 14 Dec 2013
Location: Herefordshire
Posts: 2080
When I replaced mine at 147K, although initially diagnosed with a shot centre bearing, the rear UJ was also shot & seizing up.
26th Jul 2018 6:39 pm
Huggs153
Member Since: 15 Nov 2012
Location: Surrey
Posts: 190
Having just watched Youtube, its a new shaft for me... Far to much faffing about with hammers n stuff.Huggs.
D4 XS
D3 HSE(SOLD)
side steps, EGR blanked,3 flash +Clock Move
D4 XS 2012 For sale
D4 HSE 2015
V8 Upgrade Front brakes (AF)
155000 mile+ club
RAI
16000 lb winch
D4 As it comes...
Hampshire & Berkshire 4X4 Responder
26th Jul 2018 6:55 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4674
Complete shaft removal required to fit a new centre bearing. Its a bit fiddly to do and you have to get it right first time! New bearing costs around £40, if money no option a new shaft can be fitted in around an hour or so.
26th Jul 2018 9:33 pm
Discomadness
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
To be honest i’ll Bet of you took the old shaft off the hardy spicer thing at the back would be “notchy” and knackered. New one from Bearmach was about £200. Don’t forget to replace the bolts to the rear diff also. I believe that land rover used to quote 250nm for those bolts but now have dropped it to 150nm. Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
26th Jul 2018 10:38 pm
Huggs153
Member Since: 15 Nov 2012
Location: Surrey
Posts: 190
New prop delivered and fitted in a morning. Just checking the torque setting and then replacing the heat shield job done on driveway with stands and jack. Needed jack to crack the prop from the diff end a sit was uber tight and didn't want to move...
Huggs.
D4 XS
D3 HSE(SOLD)
side steps, EGR blanked,3 flash +Clock Move
D4 XS 2012 For sale
D4 HSE 2015
V8 Upgrade Front brakes (AF)
155000 mile+ club
RAI
16000 lb winch
D4 As it comes...
Hampshire & Berkshire 4X4 Responder
14th Aug 2018 12:45 pm
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
Just changed the Centre bearing on mine.
Biggest pain was re-sealing the centre CV joint boot again afterwards!!
oh and crushing my thumb between propshaft and chassis cross member whilst lifting prop in place!!!
Now got front wheel bearings to change as something is clicking, LHS rumbling and brake discs shot!!
If things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking .. O
14th Aug 2018 1:24 pm
Huggs153
Member Since: 15 Nov 2012
Location: Surrey
Posts: 190
I avoided the crushing of digits by setting the prop on two stands and thus leaving me two hands to reach for the bolts and align the shaft... Worked well for me.Huggs.
D4 XS
D3 HSE(SOLD)
side steps, EGR blanked,3 flash +Clock Move
D4 XS 2012 For sale
D4 HSE 2015
V8 Upgrade Front brakes (AF)
155000 mile+ club
RAI
16000 lb winch
D4 As it comes...
Hampshire & Berkshire 4X4 Responder
14th Aug 2018 1:55 pm
DiscoB
Member Since: 04 Jun 2018
Location: Cardiff
Posts: 1
Steamyrotter wrote:
Just changed the Centre bearing on mine.
Biggest pain was re-sealing the centre CV joint boot again afterwards!!
oh and crushing my thumb between propshaft and chassis cross member whilst lifting prop in place!!!
Now got front wheel bearings to change as something is clicking, LHS rumbling and brake discs shot!!
Just about to change my centre bearing. What grease did you use in the CV joint? The workshop manual does not tell you anything, it says replace the whole propshaft.05 Disco 3 HSE auto
02 TD5 Defender 90
77 Series 3 88
72 Series 3 88
82 RRC
Oh and a 1983 Santana Super Turbo 88
12th Sep 2018 4:12 pm
L319
Member Since: 14 Dec 2013
Location: Herefordshire
Posts: 2080
Used to be molybdenum in CV joints.
12th Sep 2018 5:01 pm
Steamyrotter
Member Since: 03 Jul 2017
Location: Somewhere near Somewhere else in Somerset
Posts: 117
Yup got a can of Moly grease from Eurocarparts when I picked the bearing upIf things were meant to be easy, then I will soon complicate them....
Please note...
Anything I say is only from my personal experience and knowledge..
I don't assume to know everything, and know there is a lot I don't know..
But then I could be talking .. O
12th Sep 2018 5:11 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4674
Then you're all set! The tricky bit is resealing the alumimium cover but its not rocket science. Just go easy when removing it. Take your time, and a small ball pein hammer a few cloths will prove invaluable. yµ (idµ - eAµ) ψ=mψ
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum