Announcement: Please provide feedback on electronic park brake faults. Click here for more info.
|
Alternative jack when changing rims
|
|
|
|
sbarnham
Joined: 07 Nov 2007
Location: Blue Mountains
Posts: 41
 
|
| Alternative jack when changing rims |
|
Guys,
I have a second set of rims and the factory jack is such a pain -- slow and fiddly.
Wondering about getting a trolly jack, but not sure where to use it ?
Question 1: Does anyone use a trolly jack on their D3 ? What point do you lift ?
Question 2: Anyone got a better solution ?
_________________
2005 TDV6 HSE in Cairns Blue
Previously 1999 TD5 in Blenheim Silver
|
 Thu May 08 2008 11:24am |
|
|
heine
Joined: 07 Feb 2007
Location: Midrand
Posts: 1355
 
|
I use a trolley jack and also an air jack . The trolly jack has a nice big receiver plate - so I normally place it under the suspension as close to the wheel as possible
|
| Thu May 08 2008 11:53am |
|
|
d34me
Joined: 09 May 2008
Location: Kilmore
Posts: 4
|
I also have a trolley jack so that I can change my wheels for dirty weekends. I lift 1 wheel at a time from the same spot the original jack is supposed to go.
_________________
Disco 3, Gold TDV6 HSE, rear e diff, kaymar rear bar, ARB bullbar with front parking sensors, Warn winch, 110L auxiliary tank, dual battery, GME UHF, Lightforce spotties, Cooper ST's, LR snorkel, Expedition roof rack.
|
| Fri May 09 2008 1:08am |
|
|
norto
Joined: 10 Apr 2006
Location: batemans bay
Posts: 841
|
d34me welcome
Was your D3 featured in a 4wd magazine a while ago
_________________
Peter
"Global Warming" The religion of the left
|
| Fri May 09 2008 2:17am |
|
|
d34me
Joined: 09 May 2008
Location: Kilmore
Posts: 4
|
norto wrote:d34me welcome
Was your D3 featured in a 4wd magazine a while ago
It wasn't featured, but it has been in Overlander magazine for the Drive For Life trip. I didn't have a lot of the accessories back then. Is that what you are referring to, or is it mistaken identity? 
_________________
Disco 3, Gold TDV6 HSE, rear e diff, kaymar rear bar, ARB bullbar with front parking sensors, Warn winch, 110L auxiliary tank, dual battery, GME UHF, Lightforce spotties, Cooper ST's, LR snorkel, Expedition roof rack.
|
| Fri May 09 2008 3:29am |
|
|
norto
Joined: 10 Apr 2006
Location: batemans bay
Posts: 841
|
Unfortunately, mistaken identity
_________________
Peter
"Global Warming" The religion of the left
|
| Fri May 09 2008 3:39am |
|
|
PCH
Joined: 12 Jan 2005
Location: Anywhere but work
Posts: 725
|
If you get a trolley jack make sure it is at least 2.5 tonne to make lifting an easy and safe task.
I lift each corner under the chassis rail near the suspension arm then stick an axle stand under the chassis rail near the jack. There is no need to change suspension height, just do it in normal height. If you have a flat concrete surface it make it that much easier.
Chris
_________________
Rocky the 2005 Discovery 3 TDV6 HSE
ARB Bull Bar, Warn 9.5XP Winch, IPF D/Lights, Cooper STT's, LR Raised Air Intake, Traxide aux battery system, custom drawers and half height Autosafe cargo barrier towing Bullwinkle the 2006 Kimberley Karavan Limited
|
| Mon May 12 2008 2:58am |
|
|
eran48
Joined: 10 Dec 2007
Location: Sydney
Posts: 44
|
G'day,
I use a 3 ton trolley jack and pretty much have the tyre changing down to a fine art after swapping tyres about 3 times now - takes about 30 minutes to swap all 5 wheels - this includes wiping down all 10 tyres/wheels and putting the unused set away 
This is probably a no-no but I just place the trolley jack under the suspension arms and only jack enough to raise the tyre about half a centimetre off the ground. The trolley has a large round plate at the jacking end and I have a piece of rubber mat on it to prevent scratching the suspension arms.
This makes it really easy to get the wheels off and to put the second set on - there is virtually no lifting of the heavy wheels/tyres on/off the hub.
I also think this is much safer as I am literally only raising one corner wheel at a time - the car/chassis is not raised at all. I only need to raise the suspension arm a total of about 1.5 cm. This is a lot less pumping of the trolley jack compared to needing to raise the chassis about a 6 - 12 inches before the suspension reaches full droop and the wheel leaves the ground.
One thing to watch out for when jacking this way - when the suspension arm is slightly raised, the computer thinks that the car is not level and will actually level the vehicle - it WILL do this even when one or more doors are left open!  This happened last friday when I had the rear driver's side suspension arm raised slightly (tyre was half cm off the ground). The car levelled itself even though I had the front passenger and rear doors (cargo area) open.
I always thought that leaving a door open will stop the suspension from changing height but it appears that this doesn't stop it from LEVELLING itself.
Cheers.
|
| Mon May 12 2008 6:18am |
|
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
