Member Since: 11 Oct 2018
Location: Cornwall
Posts: 84
TPMS stopped working
as per title, TPMS system has stopped.
Nothing changed to my knowledge by me with IID Tool.
Enabled Remote Timed Climate a while back,
all was well with TPMS until a couple of days ago when I tried to bring up pressure check.
System worked fine with a puncture in January, and re set itself with new tyre ok.
Select tyre pressures from service menu, and all come up as zeroes !
Anyone know what the CCF settings should read ?? TPM 1 has about a dozen settings !!
"Undefined" seems wrong to me ??? MY16 D4 Graphite.
and how do I re submit handbook pressures etc.?
Had a similar issue, but had nothing whatsoever in the service menu, no warning lights on start up, nothing to say it was fitted.
The zeros displayed is what I get after it hasn’t been used for a few days, twenty metres up the road, turn the engine off, put the ignition on and it’s all ok.
If you had accidentally changed a setting with the iid tool I would expect to see errors or a warning light on startup.
30th Apr 2019 5:57 pm
Pete Hancock
Member Since: 11 Oct 2018
Location: Cornwall
Posts: 84
Thanks Washwipe, tried 20 miles (to work), stop, ignition on, still nothing.
Not even got the options to select high load / light load settings !
Could you please go into your CCF and check what the current settings are on yours ??
TPM 1
TPM 2
TPM on Spare
or anyone else on here who can do that for me ??
Still not convinced "undefined" is correct for TPM 1, but don't want to risk b*+! ering anything up.!
T. I. A. Pete.
1st May 2019 5:11 pm
philm
Member Since: 02 Oct 2016
Location: Manchester
Posts: 732
Mine reads:
TPMS 1 Undefined
TPMS 2 TPMS Fitted
TPMS on Spare yesL633 Defender
Range Rover Velar-gone
Discovery 4 Landmark-gone
Gap IID Tool
Member Since: 11 Oct 2018
Location: Cornwall
Posts: 84
update
Been into local LR dealer, ran diagnostics, and apparently the system has lost comms with all sensors. Requires tyres to be removed to get valve ID's and re-programme the system. Warranty job, but due service end of this month, so getting it done then while she's in. Keep them crossed.
14th May 2019 1:01 pm
M3bobby
Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857
Programming by number is the factory way of doing it. You should be able to drive for 10 mins and they should auto detect. Have you checked the receiver above the front courtesy lamp (location depends on MY I think).
27th May 2019 9:21 am
Pete Hancock
Member Since: 11 Oct 2018
Location: Cornwall
Posts: 84
Service / MOT 13 Jun.....TPMS fault, N/S/F sensor replaced, touch wood all ok since.
Seems strange that one sensor faulty wipes out the whole system without showing up as a fault !!!
27th Jun 2019 11:10 am
M3bobby
Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857
Was that the unit in the wheel or the antenna?
I never get a fault code and non of mine are working as I’ve not got the sensors in the wheels. I suppose the system is working but in my case the sensor isn’t available to communicate with. I posted in another thread that on Tuesday I was following a Ford Edge and my info screen said TPMS active. I must have picked up the Fords TPMS as it came back with TPMS unavailable when he turned off.
27th Jun 2019 11:23 am
Pete Hancock
Member Since: 11 Oct 2018
Location: Cornwall
Posts: 84
Not sure M3bobby.
Written on sheet as "Fit N/S/F TPMS sensor & program" so I assumed it was the wheel sensor ?
Will ask when I go in next week for Blind spot Module replacement.
27th Jun 2019 11:50 am
M3bobby
Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857
Probably sensor if it needed reprogramming (or activating).
If you can, can you get a photo of the blind spot sensor in place.
27th Jun 2019 11:57 am
Pete Hancock
Member Since: 11 Oct 2018
Location: Cornwall
Posts: 84
Very doubtful as I will be dropping it off before they open and collecting from work when done.
Presumably it is behind the rear bumper cover ?
Sorry can't be more helpful mate.
27th Jun 2019 12:25 pm
M3bobby
Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857
I probs, I have a drawing of it in place and just wanted to see it in the flesh so to speak.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
