Member Since: 15 Jan 2010
Location: Stockholm
Posts: 773
wheel arch trim
Where can I get the lower inside fastener for left side wheel arch trim.
Is there a part number?
See picture.
https://www.disco3.co.uk/gallery/albums/us...G_4437.JPGDiscovery 3, MY2008, TDV6 Auto, G4 Tangiers Orange
Discovery 4, MY2011, TDV6 Auto
crikey ... you made that picture hard to see ... just a link AND only the thumbnail version.
try this instead ...
Click image to enlarge
3rd Jun 2020 5:34 pm
urhunden
Member Since: 15 Jan 2010
Location: Stockholm
Posts: 773
Do not know what happened with the picture.
Anyway thamk you for posting it in size.
Do you have an idea on number or where the fatener can be found?Discovery 3, MY2008, TDV6 Auto, G4 Tangiers Orange
Discovery 4, MY2011, TDV6 Auto
3rd Jun 2020 9:25 pm
pwheeldon
Member Since: 15 Jan 2020
Location: West Yorks
Posts: 1445
Hi, if its the inner wing liner then these should do the job:
https://www.ebay.co.uk/itm/273168202881Discovery 4 GS 2009 Auto Stornoway Grey
Discovery 3 s 2005 Auto Bonatti Grey Gone
Discovery 3 SE 2005 Manual Zambezi Silver Gone
Range Rover Sport HSE 2006 Black
Aston Martin DB7 VV
3rd Jun 2020 10:43 pm
urhunden
Member Since: 15 Jan 2010
Location: Stockholm
Posts: 773
No it is as can be seen in the picture the bracket that is attached with two screws.Discovery 3, MY2008, TDV6 Auto, G4 Tangiers Orange
Discovery 4, MY2011, TDV6 Auto
3rd Jun 2020 11:15 pm
bcleugh
Member Since: 02 Mar 2013
Location: Newcastle
Posts: 144
its not a seperate bracket it is attached to the outer wheel arch trimD1 200TDI 3 Door (Most expensive Land Rover ever as it got me hooked)
D1 300TDI 5 door
D2 TD5
D3 100,000+ Club
D4 XS
D4 Landmark
4th Jun 2020 11:52 am
urhunden
Member Since: 15 Jan 2010
Location: Stockholm
Posts: 773
Does this mean that I have to buy a complete new Wheelarch trim to attach it again?
Or could there be some other solution?Discovery 3, MY2008, TDV6 Auto, G4 Tangiers Orange
Discovery 4, MY2011, TDV6 Auto
4th Jun 2020 12:39 pm
bcleugh
Member Since: 02 Mar 2013
Location: Newcastle
Posts: 144
Hi you can see in this image its all one piece, i have the same issue going to try and glue it with some epoxy the challenge is getting it at the right angle
Click image to enlarge
D1 200TDI 3 Door (Most expensive Land Rover ever as it got me hooked)
D1 300TDI 5 door
D2 TD5
D3 100,000+ Club
D4 XS
D4 Landmark
I'd be looking at one of the "modern silicon" adhesives (for want of a better description.)
tiger-something (half ) springs to mind.
edit : Tiger Seal. it ain't cheap but has a good reputation.
5th Jun 2020 2:14 pm
urhunden
Member Since: 15 Jan 2010
Location: Stockholm
Posts: 773
Hi hardware,
looking at the picture you attached it dos not look the same as in my wheelarch.
On yot picture fron Bearmach it is just a small thing protruding from the arch.
If you look at my picture which is from the side not damaged it is a long tab attached with a screw at the end.
Could be possible for me to make a small metal tab I can pop to the remaining little plastic and make a hole in the metal.
Anyway i think it is strange that the original tab is not a separate part.Discovery 3, MY2008, TDV6 Auto, G4 Tangiers Orange
Discovery 4, MY2011, TDV6 Auto
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum