Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Maintenance & Mods (D3)

My split charge system
Post Reply  Down to end
Page 1 of 9 123456789>
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4
My split charge system

As the weathers changing for the best I decided to install a split charge system to Vinnie mainly for running a coolbox/fridge whilst camping but to also charge phones and other bits too. After reading many other threads on here and getting some good advice regarding different methods (Iguana, Sailorboi & Nic Symonds) I decided I was going to use the T-max Split Charge System.

I'm not keen on adding extra bits to the cab of the D3 where they will be on view and pondered on a few locations to mount the T-max controller, eventually I decided for me the best location would be the upper glove box! So with this in mind I started working my way back from there towards the spare battery box under the bonnet. I drilled a small hole in the corner of the upper glove box and threaded the wires through, I then went on to route them behind the glove boxes.


Click image to enlarge



Click image to enlarge



Click image to enlarge



Then from the drivers side footwell I pushed a length of solder through to the passenger footwell to use as a pull through, taped the wires to it then pulled them back through.


Click image to enlarge



Click image to enlarge



Click image to enlarge



Click image to enlarge



From here I ran them under the carpet and over to the grommet leading to the engine bay. As you can see I pushed a screwdriver through the grommet and nearly caused myself all sorts of issues Shocked


Click image to enlarge



I then replaced the screwdriver with the solder and pulled them through into the engine bay


Click image to enlarge



Click image to enlarge



Click image to enlarge



The red wire will be too short so I will extend this to reach the main battery. This is how I will use the controller when needed


Click image to enlarge



And when not in use I will just leave it tucked away like so


Click image to enlarge
 

Last edited by Iceman08 on 2nd Aug 2017 10:03 am. Edited 5 times in total 
Post #146411326th Apr 2015 11:50 am
View user's profile Send private message View poster's gallery Reply with quote
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4

I next moved my attention to building the rear panel that will house the 12v sockets and usb sockets. I pretty much copied another forum members (Nic Symons) design for this. Firstly I cut a piece of ply to fit inside the back of the rear drivers side cubby panel


Click image to enlarge



Click image to enlarge



Then I marked out where I wanted all the items to go with a pencil and tape measure and started cutting/drilling. After I had marked out the rectangle hole for the volt gauge I then removed the ply and cut a bigger rectangle out of that too


Click image to enlarge



Until I had this


Click image to enlarge



On the back I fitted a fuse box screwed to the ply and set about wiring it all up.The blue wire and smaller wires going to the volt gauge are only temporary as I didn't have the right size cable to finish them


Click image to enlarge



Click image to enlarge



I then hooked it up to a spare battery to test it all worked.........which it did Thumbs Up


Click image to enlarge



Click image to enlarge



Click image to enlarge



Once I was happy it was all working I put the panel back into its location to see how it looked


Click image to enlarge



Next step is to source some small black screws to fit the socket surrounds on properly and then to get a yellow top Optima battery ordered as well as a battery clamp to fit the spare tray. Once that is in place I will measure up the length of cable needed from the aux battery to the rear and get my local auto electrical shop to make it up for me ready to be threaded onto it's final position.
 

Last edited by Iceman08 on 2nd Aug 2017 10:27 am. Edited 2 times in total 
Post #146411426th Apr 2015 11:51 am
View user's profile Send private message View poster's gallery Reply with quote
Andy Foster
 


Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551

United Kingdom 2015 Discovery 4 3.0 SDV6 SE Tech Auto Santorini BlackDiscovery 4

Looking good Thumbs Up

IVe just started something similar myself. Just need the cable to go from aux battery to rear cubby. I'm sure someone will know how long it needs to be.

Cheers

Andy
 D4 MY15 SE TECH
D3 gone but never forgotten. 
 
Post #146429226th Apr 2015 6:01 pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
SWR
 


Member Since: 07 Nov 2013
Location: Warwickshire
Posts: 840

England 2005 Discovery 3 TDV6 HSE Auto Bonatti GreyDiscovery 3

Looks really good. Thumbs Up
Where did you get your golf meter and sockets from please.

How thick is the plyboard you used?

Thanks

Simon
 D3 HSE TDV6 Auto. Bonatti Grey.

Mods:
V8 Brake upgrade (front Only), Full height Luggage guard, Rubber mats all round, RLD spare wheel protector, Terra Firma Steering and Transmission guard, Smoooooth Nappa steering wheel, Clock on dash and Reverse home lights. National Luna split charge system, front and rear light guards, Danhag GSM (on loan), JE stage 1 remap... Zero money
 
 
Post #146441826th Apr 2015 9:59 pm
View user's profile Send private message View poster's gallery Reply with quote
Bodsy
Site Sponsor 


Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3
Re: My split charge system

Iceman08 wrote:
From here I ran them under the carpet and over to the grommet leading to the engine bay. As you can see I pushed a screwdriver through the grommet and nearly caused myself all sorts of issues Shocked

[URL=]
Click image to enlarge
[/URL]


[URL=]
Click image to enlarge
[/URL]



Iceman, thats a really really lucky call there with that wiring.
You've gone through the wrong grommet, there is a much better one to the right of the Brake Booster tucked away into the bulkhead. You can put a screwdriver through that one with no risk to the wires.
The preferred route is the one to the right as most vehicles are Auto's and it is used only for the Manual clutch cable, so plenty big enough for the cables that are normally needed.
Thumbs Up
I like the 'box' being tucked away in the glove box. :thumbsup:

Admin note: this post has had its images recovered from a money grabbing photo hosting site and reinstated Mr. Green
 Bodsys Brake Bible

D4/D3 Remote FBH heat kits
BAS Remaps/ EGR Blank
Transmission Flush
Software updates/enabling


Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset
See It Here 
 
Post #146510228th Apr 2015 9:26 am
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Iguana
 


Member Since: 14 Oct 2013
Location: 'Sunny' Zomerset
Posts: 9402

Ukraine 

Cracking job there Thumbs Up
 Iggy/Ieuan

Current LR =
2015 RR Sport Autobiography
&
1992 Land Rover Defender Camper

- Gone but not forgotten:
MY10 D4 GS
MY05 Disco 3 'S'
MY14 FL2 HSE manual in Blue
MY15 Disco 4 HSE Lux in Santorini Black
MY08 Disco 3 SE manual in Buck Blue
1960 Series 2 88" (No idea why I sold it!) 
 
Post #146517528th Apr 2015 12:36 pm
View user's profile Send private message View poster's gallery Reply with quote
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4

SWR wrote:
Looks really good. Thumbs Up
Where did you get your golf meter and sockets from please.

How thick is the plyboard you used?

Thanks

Simon


Sorry for the late reply! The plyboard was 1/2" thick and all the other bits were off eBay.

http://www.ebay.co.uk/itm/320701838199?_tr...EBIDX%3AIT

http://www.ebay.co.uk/itm/180852412753?_tr...EBIDX%3AIT

http://www.ebay.co.uk/itm/191193093188?_tr...EBIDX%3AIT

http://www.ebay.co.uk/itm/171302373712?_tr...EBIDX%3AIT

http://www.ebay.co.uk/itm/200918695585?_tr...EBIDX%3AIT

http://www.ebay.co.uk/itm/270717638154?_tr...EBIDX%3AIT
  
Post #146546428th Apr 2015 10:28 pm
View user's profile Send private message View poster's gallery Reply with quote
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4
Re: My split charge system

Bodsy wrote:
Iceman08 wrote:
From here I ran them under the carpet and over to the grommet leading to the engine bay. As you can see I pushed a screwdriver through the grommet and nearly caused myself all sorts of issues Shocked

[URL=]
Click image to enlarge
[/URL]


[URL=]
Click image to enlarge
[/URL]



Iceman, thats a really really lucky call there with that wiring.
You've gone through the wrong grommet, there is a much better one to the right of the Brake Booster tucked away into the bulkhead. You can put a screwdriver through that one with no risk to the wires.
The preferred route is the one to the right as most vehicles are Auto's and it is used only for the Manual clutch cable, so plenty big enough for the cables that are normally needed.
Thumbs Up
I like the 'box' being tucked away in the glove box. Thumbs Up


I was slightly worried to say the least that i'd done some serious damage!

I'm guessing your referring to this grommet?


Click image to enlarge



If so it looks a million times easier to get at Banging Head Thanks for that, i'll pull the cables out and re route them through that grommet I think, and also my new positive cable for the rear will go through there too!

The glovebox was the only place I was happy with putting the controller.........so thats where it went! :thumbsup:

Admin note: this post has had its images recovered from a money grabbing photo hosting site and reinstated Mr. Green
 

Last edited by Iceman08 on 2nd Aug 2017 10:29 am. Edited 1 time in total 
Post #146546728th Apr 2015 10:34 pm
View user's profile Send private message View poster's gallery Reply with quote
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4

Iguana wrote:
Cracking job there Thumbs Up


Cheers mate, a lot of inspiration taken from your build Thumbs Up
  
Post #146547128th Apr 2015 10:36 pm
View user's profile Send private message View poster's gallery Reply with quote
SWR
 


Member Since: 07 Nov 2013
Location: Warwickshire
Posts: 840

England 2005 Discovery 3 TDV6 HSE Auto Bonatti GreyDiscovery 3

Thanks Iceman will take a look at those parts. Thumbs Up
 D3 HSE TDV6 Auto. Bonatti Grey.

Mods:
V8 Brake upgrade (front Only), Full height Luggage guard, Rubber mats all round, RLD spare wheel protector, Terra Firma Steering and Transmission guard, Smoooooth Nappa steering wheel, Clock on dash and Reverse home lights. National Luna split charge system, front and rear light guards, Danhag GSM (on loan), JE stage 1 remap... Zero money
 
 
Post #146548428th Apr 2015 11:34 pm
View user's profile Send private message View poster's gallery Reply with quote
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4

No worries, I asked at a timber merchants for an off cut of ply so it didn't cost me anything Thumbs Up
  
Post #146563129th Apr 2015 10:36 am
View user's profile Send private message View poster's gallery Reply with quote
Iceman08
 


Member Since: 22 Sep 2014
Location: Hereford
Posts: 2284

United Kingdom 2010 Discovery 4 3.0 TDV6 HSE Auto Santorini BlackDiscovery 4

A bit more progress today......

After Bodsy telling me of the better grommet to use I pulled the cables back into the drivers footwell and fed them back into the engine bay via the new improved grommet


Click image to enlarge



Click image to enlarge



I removed the siren for better access as I don't use it anyway and mounted an inline fuse holder to the inner wing behind it. I then went on to route the positive cable from the holder to the rear cubby, it still needs tidying up in the engine bay yet. The cable that was recommended was 16mm2, 110 amp.


Click image to enlarge



Click image to enlarge



Click image to enlarge



Click image to enlarge



I ran it behind the foam near the pedals and down in the corner where I fed it all the way to the rear in a duct that already houses cables


Click image to enlarge



Click image to enlarge



Click image to enlarge



Click image to enlarge



Under the little tunnel into the 2nd row area


Click image to enlarge



Click image to enlarge



Click image to enlarge



Click image to enlarge



I decided to use one of the already threaded holes for my earth so I gave it a good clean up and attached my negative lead to it


Click image to enlarge



Click image to enlarge



Click image to enlarge



I've also taken delivery of this bad boy, so hopefully not long now and it'll all be up and running 8)


Click image to enlarge
  

Last edited by Iceman08 on 2nd Aug 2017 11:22 am. Edited 5 times in total 
Post #146659030th Apr 2015 10:07 pm
View user's profile Send private message View poster's gallery Reply with quote
Bodsy
Site Sponsor 


Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

Thumbs Up Thumbs Up
 Bodsys Brake Bible

D4/D3 Remote FBH heat kits
BAS Remaps/ EGR Blank
Transmission Flush
Software updates/enabling


Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset
See It Here 
 
Post #146659230th Apr 2015 10:10 pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Jay666d
 


Member Since: 11 Feb 2014
Location: Northumberland
Posts: 753

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

Thumbs Up Awesome write up!

You really went to town on removing panels. I went the same route to get power to my roof lights, but didn't want to take all those rear panels off... Ended up fishing the wires thru with a fibreglass rod, much like you did with the solder! Mr. Green
 07 Land Rover Discovery III HSE
07 BMW 1200 GS Adventure
08 Mercedes Sprinter 
 
Post #146660630th Apr 2015 10:54 pm
View user's profile Send private message View poster's gallery Reply with quote
SWR
 


Member Since: 07 Nov 2013
Location: Warwickshire
Posts: 840

England 2005 Discovery 3 TDV6 HSE Auto Bonatti GreyDiscovery 3

Excellent Iceman,

I am following this with real interest. Thumbs Up

Any tips to remove the rear qtr plastic trimm?

Already have the split charge system in, just need to get the feed to the rear of the car now.

I also planned to use the earth that is already there inside behind the rear lights in the back corner. Any reason you didn't use that?

cheers.
 D3 HSE TDV6 Auto. Bonatti Grey.

Mods:
V8 Brake upgrade (front Only), Full height Luggage guard, Rubber mats all round, RLD spare wheel protector, Terra Firma Steering and Transmission guard, Smoooooth Nappa steering wheel, Clock on dash and Reverse home lights. National Luna split charge system, front and rear light guards, Danhag GSM (on loan), JE stage 1 remap... Zero money
 
 
Post #146661030th Apr 2015 11:00 pm
View user's profile Send private message View poster's gallery Reply with quote
Display posts from the last:  
Post Reply Back to top
Page 1 of 9 123456789>
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site