'''Parts :'''
- Tie Rod right is left: LR010671
- Tie Rod Right: QFK500020
- Tie Rod Left QFK500010
- 2 plastic collars
'''Note:
- When lifting the vehicle, put a candle, keep the jack lifting protection and placed the wheel lodged under the vehicle in case.'''
'''Obligatory passage bench alignment adjustment after an exchange of these parts.
'''
'''difficulty:'''
- 4 / 10, the most painful is to get the ball in their cone holds no hard ball.
Time to complete:
- 3 hours for both sides.
'''1) Remove the wheel and make the vehicle safe.
'''
See comment in the box "Remarks" of the first Inter.
'''1.1) Remove the cover sheet.'''
'''2) Place the 4 pieces of plastic cards.'''
Using two screwdrivers to nail up the central pawns
'''3) Asperger of releasing the lock nut''' to adjust the ball and the base of the bellows on the link rod.
'''4) Using a screwdriver or two''', unclip the plastic collar automatically taking care not to damage it and cut the plastic tie side management, taking care not to damage the bellows.
'''5) Pointing the direction to "outside"''' and loosen the ball joints (side direction) with the key Claw + deviser of the cone of the pivot ball. Using the hard ball, detaching its cone. Remove the link rod.
'''6) Pinch the connecting rod''' in a vise, loosen the nut against the ball and complete estimate it by counting the number of turns until separation of the link rod.
'''7) Slide the bellows to the thread''' and pull hard to move the thread.
In some penetrating oil or grease will facilitate the transition.
'' 8 ) On the new link rod''', the bellows back, against the nut of the ball and the ball by counting the number of round = the number of turns when removing it (phase 6) + cons tighten the nut. :
'''9) Screw the ball on the direction''', tighten without forcing the key with claw.:
'''10) Fit the bellows side management''' and the flange with a plastic tie.:
'''11) Fit the other side of the bellows''' in his throat and up the automatic white plastic collar.:
'''12) Fit the cone of the ball joint in its housing''' (pivot) and tighten the nut "nylstop". If the axis of the ball running and you could not tighten the nut, slide the handle of the key claw like the picture to keep the ball in its cone.
'''13) Replace the plastic cover and four pawns.
'''
'''14) Replace the cover sheet metal.'''
'''Obligatory passage bench alignment adjustment after an exchange of these parts.'''
photos and texts "Boubou" and his son, a French owner! Translation: marco 110 (sorry ..........) do not hesitate to correct my mistakes[/img]Marco.
-D4 sdv6 HSE 2012 , high beam assist , surround cam, tv , and a lot of nice stuff..
Member Since: 15 Nov 2009
Location: SALLES 33
Posts: 1013
Thank you, but I'm not sure of my translation ......
I hope it's still understandable, and it can help you ...Marco.
-D4 sdv6 HSE 2012 , high beam assist , surround cam, tv , and a lot of nice stuff..
Member Since: 02 Dec 2008
Location: West Yorkshire
Posts: 670
Excellent write up with great pictures, some words lost in translation, but still very good
1st Nov 2011 1:03 pm
gecko_fr
Member Since: 26 Jul 2010
Location: Near Dijon
Posts: 127
Thank you 8)
1st Nov 2011 1:46 pm
Ollram
Member Since: 04 Dec 2006
Location: Gortynia
Posts: 605
VERY useful...
did you notice a great improvement in driving/feeling of the steering wheel???
14th Dec 2011 8:07 am
georgedb
Member Since: 29 Mar 2013
Location: Gauteng
Posts: 81
Matty 2332 wrote:
some words lost in translation,
Sounds very much like the SA gov
19th Mar 2014 5:17 pm
Narpy
Member Since: 18 Jul 2011
Location: Stockport
Posts: 7830
Will require proper 4 wheel alignment after this install to prevent errors. Mods:
Front Fogs + Halos
FBH Remote Control
The 1st Ever RRS Modded Grill
Garmin Nuvi + D4 Surround + Reversing Camera.
D4 Steering Wheel.
Rear Boot Spoiler.
Twin Brake Lights.
Wing Mirror Indicator Repeaters.
Long Roof Rails
Make your own Narpy grill thread
I'm not scared, I'm outta here.
19th Mar 2014 6:00 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18457
As the bushes aren't touched then "just" adjusting the tracking should suffice. But a full alignment check is no bad thing 06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
19th Mar 2014 6:02 pm
thorgal
Member Since: 26 Nov 2008
Location: on the east side
Posts: 541
Do you guys know the size of the inner tie rod ball socket.I will try to rent a tool for removing inner tie rod ball, but not sure of the appropriate size.Please help ?
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum