Member Since: 21 Oct 2016
Location: kent
Posts: 13670
desperate help plse with fitting drivers electric seat only
hi
can u fit just the drivers electric seat please
or do u have to also fit the passengers seat at the same time
been looking at the wiring diagram and not sure if the power goes into the passenger side seat first then across to the drivers side
is only because it's so cold of quickly removing my manual seat and putting in the drivers electric seat , can then do the passengers side later
thks again
Last edited by gstuart on 30th Nov 2016 2:29 pm. Edited 1 time in total
30th Nov 2016 11:33 am
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
You can do them one at a time. They will work independently.
30th Nov 2016 11:37 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
ah bless u irwin
may i ask which wire the power comes into the seat , is it the purple connector
found this drivers seat has the memory ecu on it, but not worried if that works or not
changed over drivers seat to my cloth interior
was thinking when i do the passengers side if i can remove the seat squab seat belt warning pad
as there all coming apart anyway
found the wiring centre block very clever, where u cant put a connector into the wrong bit , one that has ford on it
thks so much once again
30th Nov 2016 11:41 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
plugged it all in , nothing
checked fuses they are ok
any ideas please guys
nothing works on the seat
thks again
ps also turned on the memory function in the ccf , know i'm not bothered but turned it on anyway
30th Nov 2016 12:44 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
latest fault ref the memory module is missing a message
do i need to turn that off plse
in a bit of a pickle
30th Nov 2016 12:46 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
right , turned off the memory module and heated seat function
just trying to get the seats to work but nothing
only got the drivers seat fitted at the moment
heeeeeeeeeeeellllllllllpppppppppp
30th Nov 2016 12:59 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
On the multi connector, there should be a yellow,blue,purple,black etc...connectors. The black connector in the middle carries the power. 2 big wires, +|-, check that those wires are matching up on the seat and car connectors.
30th Nov 2016 1:09 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
ur a diamond , out in the car at the moment
just took a quick pic of the wires i have
i do appreciate this great help
30th Nov 2016 1:15 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
can i rob the wiring loom from the passenger seat please
seeing it hasn't got the memory func ???
30th Nov 2016 1:17 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
heeeeeeeeelllllllllllppppppppppp
think i may have to take the seats all back out again and refit my manual one
done a search , not worried about the memory or heated seat function
am really lost , not as easy as i thought
just wish to get the motors to work
sorry being such a pain
30th Nov 2016 2:30 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
Yes, try the passenger seat loom. I did that when I installed 2012 RRS seats.
30th Nov 2016 3:23 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
no good seems very different
right , thks for this by the way ,
this is what i've done
disconnected the seat air bag and seat belt tensioner out of the way
i've got a 12 volt feed going into the ford multi connector , which is permanent , even with the key out on the following wire
brown with a green stripe
black which i assume is the ground earth
on the other side of the connector there is nothing
so have a 12 volt supply at the seat but not going into the loom , as the black connector is not on the other side of the ford multiplug
thinking on the passenger loom there's a black connector , if i cut that off so can use it for the drivers side , where does that need to go to please
have got the memory ecu box fitted , not worried about the memory function or heating, just the motors
thks for this and so, so grateful
30th Nov 2016 3:49 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13670
pics are of the connector that goes into the memory ecu box
would this be the connector that supplies the ecu box with power
wondering if i cut off the black connector from the passenger loom, put the black plug into the ford multiconnector
then cut it into the back of the plug that goes into the memory ecu
what do u think please or am i going down the wrong route
as i assume that i need to get 12 volts into the memory box or is it somewhere else that the loom needs to be powered
thks
just trying to slowly work it out , but hands up am rather lost to say the least , lol
30th Nov 2016 3:58 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
Those look like the wires you need to provide power to, large browngreen and black wires.
30th Nov 2016 4:33 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
There is another thread on the forum where they installed these seats and they joined the electronic live and earth to the larger live and earth wires on the seat loom and then connected them up to the multiplug live and earth wires. That thread should help you.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum