TonyH
Member Since: 01 Mar 2006
Location: Market Drayton, Shropshire
Posts: 211
|
Replacing rear wiper motor |
|
Hi folks,
I need your help, I would like some step-by-step instructions for replacing the rear wiper motor on my 06 Discovery3. The bit that concerns me most is removing/replacing the plastic panel.
Your advice would be appreciated.
Thanks' in advance *Disco3 7-seat Auto
March 2006
Zermatt silver
*Disco TD5 GS Manual
2001
Epson Green
108,000 miles without a single problem
*Disco TD200 Manual
1993
Bonatti Grey
55,000 trouble-free miles
*Various company cars, no comparison
|
11th Nov 2011 11:18 am |
|
|
rangehelper
Member Since: 04 Nov 2011
Location: Maidstone
Posts: 52
|
Interior Trim and Ornamentation - Liftgate Trim Panel
Removal and Installation
Removal
1. Remove the liftgate trim panel.
• Remove the screw.
• Release the 11 clips.
2. Remove the liftgate striker trim panel.
3. NOTE: Do not disassemble further if the component is removed for access only.
Remove 6 clips from the liftgate trim panel.
Installation
1. To install, reverse the removal procedure.
Wipers and Washers - Rear Wiper Pivot Arm
Removal and Installation
Special Tool(s)
General purpose puller
100-005A (LRT-99-500A)
Removal
1. Noting the fitted position and using the special tool, remove the rear wiper pivot arm.
• Remove the nut cover.
• Remove the nut.
2. NOTE: Do not disassemble further if the component is removed for access only.
Remove the wiper blade.
• Release the clip.
Installation
1. To install, reverse the removal procedure.
• Tighten the nut to 15 Nm (11 lb.ft).
Wipers and Washers - Rear Window Wiper Motor
Removal and Installation
Removal
1. Remove the liftgate trim panel.
For additional information, refer to: Liftgate Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
2. Remove the rear window wiper arm.
For additional information, refer to: Rear Wiper Pivot Arm (501-16 Wipers and Washers, Removal and Installation).
3. Remove the rear window wiper motor.
• Disconnect the electrical connector.
• Release the clip.
• Remove the 3 nuts.
4. NOTE: Do not disassemble further if the component is removed for access only.
Remove the 3 rubber insulators.
• Remove the metal inserts.
Installation
1. To install, reverse the removal procedure.
• Tighten the nuts to 10 Nm (7 lb.ft).
If you need images Throw me your e-mail
|
11th Nov 2011 12:58 pm |
|
|
Duffer
Member Since: 30 Jun 2013
Location: Pembridge
Posts: 44
|
Just about to embark on this job myself.
Images would be great.
Anyone have any?
Duffer SWB S111 V8
LWB S111 2 1/4
You're never late with a V8!
|
22nd Jun 2016 11:43 am |
|
|
lynalldiscovery
Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274
|
Remove the plastic panel from the lowest part first as the top is held on with metal spring clips, I thought it was going to break at first then thought sod it its coming off regardless!
|
22nd Jun 2016 12:56 pm |
|
|
Duffer
Member Since: 30 Jun 2013
Location: Pembridge
Posts: 44
|
Any clips I should get in stock before hand (part No)? I guess some will break.
D SWB S111 V8
LWB S111 2 1/4
You're never late with a V8!
|
22nd Jun 2016 1:14 pm |
|
|