Member Since: 21 Oct 2016
Location: kent
Posts: 13673
Tow electrics socket pins/terminals (updated)
hi
UPDATED
please scroll through to page 2 for details
would anyone be so kind if they know where i can get the following pins from plse
noticed on some other grey connectors there marked ford
tried to put as much details as possible
thanks so much in advance
Last edited by gstuart on 8th Feb 2018 7:18 pm. Edited 2 times in total
2nd Feb 2018 5:52 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18468
tow socket loom?06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
2nd Feb 2018 6:56 pm
Batfink
Member Since: 31 May 2017
Location: Isle of Sheppey
Posts: 1510
Have you tried Maplins or RS components?2006 TdV6 HSE.
2nd Feb 2018 7:50 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13673
Martin wrote:
tow socket loom?
hi, you’ve got a sharp eye
it is indeed for the 12 s socket , already made part of the loom but after searching for hours can’t seem to find the pins , or even tracking down the connector that comes with the spare pins
Last edited by gstuart on 3rd Feb 2018 1:13 am. Edited 1 time in total
3rd Feb 2018 12:52 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13673
Batfink wrote:
Have you tried Maplins or RS components?
forgot about them, thks will have a look
3rd Feb 2018 12:52 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13673
nope , still can’t find these pins
heeeeeeeeeeeelllllpppp,
pretty please with a cake on top
3rd Feb 2018 3:06 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10385
The earlh just goes to an eyelet stud.
I'm sure you could just cut some insulation off the LR wire and solder to the copper.
3rd Feb 2018 9:30 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13673
hi pete
u must have a crystal ball as i was just thinking the same after finding these 3 way splice connectors
i can just take out the wire and link it onto an ordinary spade connector via the inline fuse , so the existing loom is all put back as it should be and have a safe terminal for the 12 s cable
what do i think , ref the pic plse
3rd Feb 2018 9:33 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10385
Does that thick green brown go anywhere on your tow bar loom ?
If it does maybe you have a twin socket loom ?
And further exploration under car required ?
Or look around towfuses.
Do you have 2 15A ones with wires?
3rd Feb 2018 9:44 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13673
hi
apologises , the wires in the pictures are from an old electric seat loom, as i found one of the connectors had the same type of pin
have included pictures of the towing wires from the landy
i’ve had a good route around and can’t see any fuses on the 12n socket , was actually going to remove it, remove the insulation tape that’s been done before so it’s all put back properly
so in the future if i ever decide to re connect the 12n i can get a dedicated loom
have got an inline fuse which i will fit a 15amp rated fuse for the 12s
assume it’s ok to just have the 12s socket installed
3rd Feb 2018 10:13 am
Mikeyb
Member Since: 08 Nov 2016
Location: Maldon, Essex
Posts: 515
not checked if they supply exactly what you need but they have extensive related stock. plenty of similar companies also on the webNot such a Disco Newbie now!
IID BT
3rd Feb 2018 10:19 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13673
hi many thks for the link and will have a look
most appreciated
3rd Feb 2018 10:25 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10385
Arh. I see. So previous owner didn't use a genuine LR loom, and you are wanting pins to possible sort this out in future.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum